My wife had a shoulder repair operation yesterday at St. Luke's, and pretty much the whole day was spent with getting her checked in, surgery, post-op. I probably should have brought my laptop, but I wasn't expecting the entire day to get consumed. I will say that I am always very impressed with the medical and support staff at St. Luke's (and every other hospital here in the Boise area). Friendly; courteous; concerned.
She is doing okay, but considering that they went in and removed bone spurs inside her shoulder, she is in a bit of pain. I stayed home yesterday and today to take care of her; I just can't imagine what single people do in these situations.
The evenings have been lost in the great telescope rebuild. I discovered that all the work I put into trimming the C-channel pieces down was a mistake; there was not enough clearance for attaching the steel straps without a lot more precision in cutting than I could easily do with a bandsaw, so I started over, and it was much faster. When drilling the attachment holes in the steel straps, the straps are thin enough that they briefly went red-hot as I drilled them! (More oil next time.)
The new versions were faster to make, in spite of breaking the 1/8" end mill that I was using to cut the slot. I finished with a 1/4" end mill, which looks less elegant for an .030" thick piece of steel strap, but it isn't like you can find a 1/8" end mill in Horseshoe Bend.
The upper picture shows the static end of the strap; the lower picture shows the screw that tightens it down. Unfortunately, the thumb screws I bought at Grainger just weren't long enough. A 1" long screw thread sounds good enough, but once the captive nuts were on it, that was not enough travel to be useful, so it now has a conventional hex head bolt. I may replace those when I can order a thumb screw with a longer thread. They work well -- although it takes a while to crank them down enough. Of course, that also makes it less likely that I will overcompress the tube with the straps, so I guess that's a positive.
The mirror cell has turned out to be a "I was too clever for my good" moment (as have several in the project). It turns out that having the mounting brackets separate from the bottom plate was a great idea -- except that the bolts holding the brackets to the bottom plate can't get past the mirror once the brackets are mounted inside the tube. So I guess I will do what I was trying to avoid -- tap the mounting brackets so that I can screw the threads in from the outside of the tube. This is a blind operation, but at least I can see the brackets from the rear. Some other mirror cells have you trying to find the threaded holes in a circular casting where there are no real clues as to location. The slots in the mounting brackets were for 1/4"-20 bolts, so it is easy enough to tap these for 5/16"-18 bolts -- which, fortunately, I have some in black oxide finish that I can use for this.
But that will be tomorrow night, or maybe the night after. I actually have ScopeRoller orders rolling in, and I need to get some of these filled.
Rabu, 22 Mei 2013
Selasa, 21 Mei 2013
I Have A Philosophical Problem With Seat Belt Laws
But here's a warning that if you really prefer bouncing around the inside of your car in the event of an accident, be prepared for increased enforcement of the law. From May 20, 2013 KIVI channel 6:
The Caldwell Police Department and other Idaho law enforcement agencies will be stepping up seatbelt enforcement starting May 20th through June 2nd.
Over 70 Idaho law enforcement agencies will begin dedicating extra hours and patrols to educate and enforce the state’s safety restraint law during a 14-day period including Memorial Day.
Senin, 20 Mei 2013
No Wonder Ken Dauzat's Rings Didn't Respond...
Ken's Rings is now closed as of April 15, 2012 and is no longer taking orders.Unfortunate. He made a nice product.
Minggu, 19 Mei 2013
How To Attach The Tube (Cont.)
Here's a diagram of a simple to build tensioner for nylon webbing, stainless steel strap, or even belts.
The fixed side attachment doesn't move; I tap this side of the C-channel for a 1/4"-20 bolt. Depending on the strapping material, I may need a large washer to distribute load across more surface area. For nylon webbing, I would triple the layers for this attachment point.
The adjustment side attachment consists of a 1/4"-20 tapped hole and a bolt (probably a thumbscrew) with two nuts locked in position at the end of the bolt. The way that I have found works most easily for this is to drill through a hex head nut into the bolt, tap the hole for 6-32 threads, and use a 6-32 set screw to lock bolt and nut together. The strap goes through the slot in the side of the C-channel, and is held by two washers inside the captive nuts. The strap can rotate between the washers, so it isn't a tight fit there. You have to the get the length of the strapping pretty precisely correct for a snug fit, and then you turn the thumbscrew to clamp everything down. This also gives some room for strap stretch over time. If you reach the limits of the bolt, you can redrill the holes on the fixed side attachment, but I am considering this a short-term solution to the problem.
Limiting yourself to a thumbscrew not only simplifies tool-free adjustment, but also reduces the change of putting so much force on the tube that it damages it.
UPDATE: Good news: I asked my pastor this morning where I would steel strapping material on a weekend. He just happened to have a 50 foot roll of .030" thick, 1 inch wide steel strapping material. I started work on the device above to use some of this. I discovered that the vertical mill definitely works better with the longer screw holding everything together; I also discovered that once again, the single most important factor in milling is getting the workpiece really well clamped in position. Anything that lets it jostle in the vise is a problem. I also discovered that the 1/4"-20 thumbscrews I had...were something metric, not 1/4"-20. I guess I will buy two of those tomorrow.
The fixed side attachment doesn't move; I tap this side of the C-channel for a 1/4"-20 bolt. Depending on the strapping material, I may need a large washer to distribute load across more surface area. For nylon webbing, I would triple the layers for this attachment point.
The adjustment side attachment consists of a 1/4"-20 tapped hole and a bolt (probably a thumbscrew) with two nuts locked in position at the end of the bolt. The way that I have found works most easily for this is to drill through a hex head nut into the bolt, tap the hole for 6-32 threads, and use a 6-32 set screw to lock bolt and nut together. The strap goes through the slot in the side of the C-channel, and is held by two washers inside the captive nuts. The strap can rotate between the washers, so it isn't a tight fit there. You have to the get the length of the strapping pretty precisely correct for a snug fit, and then you turn the thumbscrew to clamp everything down. This also gives some room for strap stretch over time. If you reach the limits of the bolt, you can redrill the holes on the fixed side attachment, but I am considering this a short-term solution to the problem.
Limiting yourself to a thumbscrew not only simplifies tool-free adjustment, but also reduces the change of putting so much force on the tube that it damages it.
UPDATE: Good news: I asked my pastor this morning where I would steel strapping material on a weekend. He just happened to have a 50 foot roll of .030" thick, 1 inch wide steel strapping material. I started work on the device above to use some of this. I discovered that the vertical mill definitely works better with the longer screw holding everything together; I also discovered that once again, the single most important factor in milling is getting the workpiece really well clamped in position. Anything that lets it jostle in the vise is a problem. I also discovered that the 1/4"-20 thumbscrews I had...were something metric, not 1/4"-20. I guess I will buy two of those tomorrow.
Sabtu, 18 Mei 2013
Telescope Project Marches On
There was some pooling of paint at the bottom of the tube when I painted the first coat with the tube on end, so for the second coat, I went back to the suspension approach that I used when applying the fiberglass resin.
The method of holding the tube in the air at that stage wasn't very good, because sometimes the tube started rocking, and then the aluminum tube holding it would go flying off the chairs. So I came up with a way to prevent the aluminum tube from getting too far afield:
Unlike the first coat, which did not stick spectacularly well to the fiberglassed Sonotube, the second coat stuck quite well. It still wasn't very even, so I sanded it after the second coat as well, which again evened out the surfaces a bit (although taking off a bit of paint in the process). There were still some pretty big depressions caused by air pockets in the area where I had used fiberglass cloth, so I mixed a bit more resin, and tried to fill in the holes.
I still won't call the result, after the third coat, "beautiful," but I think it will do, at least until I can talk myself into believing that the big money for a carbon fiber composite tube that weighs 13 pounds less makes sense:
I mentioned a few days back that I was going to epoxy some steel rod on either side of the center line of the tube where it attaches to the dovetail plate to prevent rocking, which would eventually damage the tube. Then, yesterday, I mentioned that it would be better to have tube rings that lock onto the outside of the tube and screw directly to the dovetail plate.
I am still waiting on a price quote on those rings, and I started thinking. I noticed that at the edges of the dovetail plate there are a bunch of 1/4" holes. Hmmm. Could I mount supports in those holes to prevent rocking? My first thought was to machine some 1/4" (or perhaps slightly longer) plugs that would provide the support? I could even just use 1/4" hex head bolts; the heads would provide just the right elevation to prevent rocking (although at the risk of marring the surface of the tube).
But the more I thought about it (and was glad that enamel dries so slowly), it occurred to me there was an even better solution that gives me the flexibility to rotate the tube, not drill permanent mounting holes, solve the rocking problem, and involves minimal use of materials.
1. I take the C-channel which was used to mount the old scope to the dovetail plate, and cut off two 2" sections (preferably the ones that have 1/4" through holes already).
2. Shorten the legs of the C-channel down to 1/16" inch (since I no longer need long legs for stiffness of the section). Now I have a round tube to flat base adapter.
3. Drill and tap 1/4"-20 holes in each side of the two sections.
4. Buy four leather belts at the thrift store. (I need about 60 inches total length, and preferably 1 3/4" wide belts.)
5. Use a 1/4"-20 bolt and a washer to hold one end of each belt to each side of the C-channel.
6. Use the belt buckles to secure the tube to the C-channel sections. (This means that I will need to get roughly similar belt buckles when picking out belts.)
7. Perhaps drill some holes in these belts to get them in a position where I can tighten down the tube without crushing it marring the surface much.
Now I have the 60 pound or so telescope load held by two belts, which is, I think, sufficient to prevent anything from moving or working loose.
An alternative would be to look for some flexible 2" wide stainless steel straps, and apply felt to the inside to protect the tube. But then I have to figure out a way to secure the steel straps so that they can be loosened without having falling completely off. The Cave Optical mount that I had long ago used this approach, with a screw brazed into one end of the strap, so that you could loosen the straps at one end, rotate the tube, then retighten. If I could find something like this (with roughly 60" long straps) that had some way to tighten and loosen tension, this would be preferable. But the belts might be a quick way to get the telescope operational, and then worry about rings at a later time.
UPDATE: Or Velcro? This claims that the closure shear strength is 11.0 pounds per square inch. I can buy a 15 foot by 2" wide piece of Velcro at Home Depot for $28.97, what they call industrial strength Velcro. If I had ten inches of overlap of hook and loop (and if I understand what they are claiming for the closure shear strength), that would be 220 pounds per strap. That seems more than enough. It would not be as elegant as aluminum rings, but it would be light, I could pick up the Velcro tomorrow, and put the telescope together tomorrow afternoon.
UPDATE 2: Or perhaps use nylon webbing with buckles. The webbing has a tensile strength of 5500 pounds (probably more than the buckles that come with it or where I would attach it).
UPDATE 3: The more I think about it, nylon webbing and Velcro are likely to stretch under load, and that sounds a bit dangerous. If I can find some steel straps at Home Depot, I could put a bolt through the adjustment end, and use a wing nut to tension it.
The method of holding the tube in the air at that stage wasn't very good, because sometimes the tube started rocking, and then the aluminum tube holding it would go flying off the chairs. So I came up with a way to prevent the aluminum tube from getting too far afield:
Unlike the first coat, which did not stick spectacularly well to the fiberglassed Sonotube, the second coat stuck quite well. It still wasn't very even, so I sanded it after the second coat as well, which again evened out the surfaces a bit (although taking off a bit of paint in the process). There were still some pretty big depressions caused by air pockets in the area where I had used fiberglass cloth, so I mixed a bit more resin, and tried to fill in the holes.
I still won't call the result, after the third coat, "beautiful," but I think it will do, at least until I can talk myself into believing that the big money for a carbon fiber composite tube that weighs 13 pounds less makes sense:
I mentioned a few days back that I was going to epoxy some steel rod on either side of the center line of the tube where it attaches to the dovetail plate to prevent rocking, which would eventually damage the tube. Then, yesterday, I mentioned that it would be better to have tube rings that lock onto the outside of the tube and screw directly to the dovetail plate.
I am still waiting on a price quote on those rings, and I started thinking. I noticed that at the edges of the dovetail plate there are a bunch of 1/4" holes. Hmmm. Could I mount supports in those holes to prevent rocking? My first thought was to machine some 1/4" (or perhaps slightly longer) plugs that would provide the support? I could even just use 1/4" hex head bolts; the heads would provide just the right elevation to prevent rocking (although at the risk of marring the surface of the tube).
But the more I thought about it (and was glad that enamel dries so slowly), it occurred to me there was an even better solution that gives me the flexibility to rotate the tube, not drill permanent mounting holes, solve the rocking problem, and involves minimal use of materials.
1. I take the C-channel which was used to mount the old scope to the dovetail plate, and cut off two 2" sections (preferably the ones that have 1/4" through holes already).
2. Shorten the legs of the C-channel down to 1/16" inch (since I no longer need long legs for stiffness of the section). Now I have a round tube to flat base adapter.
3. Drill and tap 1/4"-20 holes in each side of the two sections.
4. Buy four leather belts at the thrift store. (I need about 60 inches total length, and preferably 1 3/4" wide belts.)
5. Use a 1/4"-20 bolt and a washer to hold one end of each belt to each side of the C-channel.
6. Use the belt buckles to secure the tube to the C-channel sections. (This means that I will need to get roughly similar belt buckles when picking out belts.)
7. Perhaps drill some holes in these belts to get them in a position where I can tighten down the tube without crushing it marring the surface much.
Now I have the 60 pound or so telescope load held by two belts, which is, I think, sufficient to prevent anything from moving or working loose.
An alternative would be to look for some flexible 2" wide stainless steel straps, and apply felt to the inside to protect the tube. But then I have to figure out a way to secure the steel straps so that they can be loosened without having falling completely off. The Cave Optical mount that I had long ago used this approach, with a screw brazed into one end of the strap, so that you could loosen the straps at one end, rotate the tube, then retighten. If I could find something like this (with roughly 60" long straps) that had some way to tighten and loosen tension, this would be preferable. But the belts might be a quick way to get the telescope operational, and then worry about rings at a later time.
UPDATE: Or Velcro? This claims that the closure shear strength is 11.0 pounds per square inch. I can buy a 15 foot by 2" wide piece of Velcro at Home Depot for $28.97, what they call industrial strength Velcro. If I had ten inches of overlap of hook and loop (and if I understand what they are claiming for the closure shear strength), that would be 220 pounds per strap. That seems more than enough. It would not be as elegant as aluminum rings, but it would be light, I could pick up the Velcro tomorrow, and put the telescope together tomorrow afternoon.
UPDATE 2: Or perhaps use nylon webbing with buckles. The webbing has a tensile strength of 5500 pounds (probably more than the buckles that come with it or where I would attach it).
UPDATE 3: The more I think about it, nylon webbing and Velcro are likely to stretch under load, and that sounds a bit dangerous. If I can find some steel straps at Home Depot, I could put a bolt through the adjustment end, and use a wing nut to tension it.
Jumat, 17 Mei 2013
Roll Your Own (Rings, That Is)
The quick but inflexible solution for attaching a telescope to the dovetail plate is to drill holes in the tube and turn bolts through the tube into the threaded holes on the dovetail plate. The more elegant solution (because it lets you rotate the tube into more useful viewing positions, with a little bit of effort) is to use rings like these. I have bought Ken Dauzat's rings before for another telescope, and I was very pleased with them. I have asked for a quote for the monster tube, and I am shuddering a little at the likely price.
But I saw this device for rolling your own rings from either tubing or flat. It's $169, but that doesn't seem like a particularly high price if it comes out the same price as buying one pair of rings. Does anyone have experience using such a tool?
But I saw this device for rolling your own rings from either tubing or flat. It's $169, but that doesn't seem like a particularly high price if it comes out the same price as buying one pair of rings. Does anyone have experience using such a tool?
Langganan:
Postingan (Atom)
